Spokane Create Delta Printer - Printable Version +- Spokane Create! Forums (http://forum.spokanecreate.org) +-- Forum: Spokane Create! (http://forum.spokanecreate.org/forumdisplay.php?fid=1) +--- Forum: Projects (http://forum.spokanecreate.org/forumdisplay.php?fid=4) +--- Thread: Spokane Create Delta Printer (/showthread.php?tid=227) |
RE: Spokane Create Delta Printer - ABearden - 07-22-2015 STLs for the carriages. The test carriage worked well, though I once again had to get Chris' help because unless you have an over abundance of belt it's difficult to clamp it together with two hands. Still to come: - Other two carriages. - Wiring & routing. - Configuration & measurements. RE: Spokane Create Delta Printer - ctcollins9 - 08-05-2015 http://m.aliexpress.com/item/2041826923.html?productId=2041826923&productId=2041826923&productId=2041826923&product=%7B%22adminSeq%22%3A202199972%2C%22aeProductSKUEsiDTOs%22%3A%5B%7B%22skuPrice%22%3A5.34%7D%5D%2C%22isSkuProperty%22%3Afalse%2C%22lot%22%3Afalse%2C%22multiUnitName%22%3A%22pieces%22%2C%22numberPerLot%22%3A1%2C%22oddUnitName%22%3A%22piece%22%2C%22offlineDate%22%3A1439945111000%2C%22productId%22%3A2041826923%2C%22productMaxPrice%22%3A5.34%2C%22productMinPrice%22%3A5.34%2C%22seotitle%22%3A%22FreeShipping!!+Long-distance%2C+3D+Printer+J-head+Hotend+for+1.75mm%2F3.0mm+E3D+Bowden+Extruder+0.2mm%2F0.3mm%2F0.4mm+Nozzle+Optional%22%2C%22shopNumber%22%3A721071%7D&category=%7B%22categoryName%22%3A%22Other+Electronic+Components%22%2C%22categoryUrl%22%3A%22http%3A%2F%2Fwww.aliexpress.com%2Fcategory%2F4099%2Fother-electronic-components.html%22%7D&productSubject=FreeShipping-Long-distance-3D-Printer-J-head-Hotend-for-1-75mm-3-0mm-E3D-Bowden-Extruder&productSubject=FreeShipping-Long-distance-3D-Printer-J-head-Hotend-for-1-75mm-3-0mm-E3D-Bowden-Extruder&tracelog=wwwdetail2mobilesitedetail $5 hotends RE: Spokane Create Delta Printer - ABearden - 08-19-2015 It moves! Got the firmware updated and the motors plugged in so I got it to move at the Spark event tonight. Now to:
RE: Spokane Create Delta Printer - ABearden - 09-20-2015 Hey, hey guys. Guess what? [attachment=126] It needs extruder calibration, and the nozzle might be smaller than it's labeled, but it's printing! RE: Spokane Create Delta Printer - ctcollins9 - 09-21-2015 Woohoo! Definitely ready for some calibration, but good job! RE: Spokane Create Delta Printer - Dan - 09-21-2015 NICE! good job dude! RE: Spokane Create Delta Printer - ABearden - 09-21-2015 (09-21-2015, 06:29 AM)ctcollins9 Wrote: Woohoo! Definitely ready for some calibration, but good job!Calibrated it today. Extruder steps/mm were 2/3rds of what they needed to be due to the Greg's extruder gearing. I need to level the glass and/or add a z-probe, but it prints pretty nice. Plenty fast too. Just a little bit of rounding on the corners @ 200mm/s due to flex. Going to add some rubber bands on the rods to see if I can control that a little bit. (09-21-2015, 06:44 AM)Dan Wrote: NICE!Thanks, but I definitely didn't solo this build! You did awesome on the CAD and plenty of others helped out with both cost and build (Chris, Nate, & John off the top of my head). Time to print! RE: Spokane Create Delta Printer - Dan - 09-22-2015 Here are a couple of pictures from the 1st, 2nd, and 3rd print. [attachment=128] [attachment=127] RE: Spokane Create Delta Printer - ABearden - 09-27-2015 Sheesh, we get ours done and someone has to show us up: http://www.digitaltrends.com/cool-tech/wasp-set-to-unveil-worlds-biggest-delta-3d-printer/ RE: Spokane Create Delta Printer - n8cutler - 09-27-2015 (09-27-2015, 10:26 AM)ABearden Wrote: Sheesh, we get ours done and someone has to show us up: http://www.digitaltrends.com/cool-tech/wasp-set-to-unveil-worlds-biggest-delta-3d-printer/ Makes me want to print a huge clay Batman! |