Location

We've moved!
213 E Ermina Ave, Spokane WA, 99207

Hours

5:30pm - 8:30pm Wednesday
New? Stop by for a tour at 6:30pm on Wednesdays

Thanks for supporting your
community 501(c)(3) makerspace


Thread Rating:
  • 2 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Laser Engraving on My Kossel Clone/ Expanding My Build Area
03-26-2015, 10:47 PM, (This post was last modified: 03-29-2015, 01:43 PM by ABearden.)
#21
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
http://www.visualnews.com/2015/03/mind-b...the-world/

Stuff like this makes me see the advantage of lasers....
Reply
04-17-2015, 10:37 AM,
#22
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
Found something that might be useful for your build plate: http://www.instructables.com/id/Detaille...-Assembly/
Reply
04-17-2015, 01:02 PM,
#23
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
Thanks Arthur. Maybe we could try doing this next week if I got the parts.
Reply
06-06-2015, 09:28 AM,
#24
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
Look at what 2 minutes of calibration got me Smile. I'm not sure if you seen it or not, but I left 2 of my vases at SC for you to compare to the print quality of your delta! Wink

https://www.dropbox.com/s/fwnr0a668haviq...4.jpg?dl=0
Reply
06-06-2015, 12:10 PM,
#25
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
(06-06-2015, 09:28 AM)ctcollins9 Wrote: Look at what 2 minutes of calibration got me Smile. I'm not sure if you seen it or not, but I left 2 of my vases at SC for you to compare to the print quality of your delta! Wink

https://www.dropbox.com/s/fwnr0a668haviq...4.jpg?dl=0

Awesome! Gotta love a dead-on print calibration. Is that build plate nice and level now, too?

I saw, they're actually at my house with the rest of the parts. It's coming together. So far I have 7/12 brackets. Still have 3 carriages and tensioners to print. Getting about 3 prints a day (10 hours). Just about to go setup the CNC to cut the frame plates. I'm hoping I can dial it in as well as yours is and your vases don't remain a point of envy. Then I'll have to send you a vase 16" tall. Big Grin
Reply
06-06-2015, 12:23 PM,
#26
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
Sounds good. Yes, my bed leveling is working perfect with the kossel bed level probe set up. Also, if I wanted to send something to SC, who/where should I send it to?
Reply
06-06-2015, 01:02 PM, (This post was last modified: 06-06-2015, 05:24 PM by ABearden.)
#27
RE: Laser Engraving on My Kossel Clone/ Expanding My Build Area
Per the http://www.SpokaneCreate.org homepage:

EDIT: address changed. Pulled the wrong one from the homepage.

840 E Spokane Falls Blvd
Bay #1
Spokane, WA 99202
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)